水平斜插板透空式防波堤消波性能数值模拟

通过改进已有的防波堤模型，建立了一种新型水平斜板透空式防波堤模型。基于VOF方法建立了波浪与水平斜板防波堤相互作用的数值模型。经数值模拟研究了该新型水平斜板防波堤结构对波浪透射系数的影响，主要考虑了斜板角度、波陡、相对板间距、相对板宽和相对出水高度等因素对防波堤消波效果的影响。模拟结果显示:①水平斜插板透空式防波堤比水平板透空式防波堤的消波效果好。在斜插板作用下，随着斜板角度增大，透射系数逐渐增大，但增幅逐渐减小；②随着波陡增大，透射系数先减后增；③随着水平板间距增加，透射系数增大；④随着防波堤相对板宽的增大，透射系数逐渐减小；⑤随着防波堤出水高度增加，透射系数先减后增。结果表明，该新型结构防波堤的消波效果显著，可以很好地消减波浪，应用前景良好。     

铝合金三角形波纹夹芯板对平头弹抗冲击特性数值模拟研究

为研究铝合金三角形波纹夹芯板对平头弹体的抗冲击性能及损伤特性，利用有限元软件ABAQUS/Explicit建立弹体冲击靶板的数值模拟模型，并结合实验验证了模型及其参数的有效性。基于数值计算结果，分析了三角形波纹夹芯板几何结构对其防护性能、失效模式和能量吸收的影响规律及机理，并与等面密度单层板进行对比分析，研究结果表明，靶体几何结构对其抗冲击性能存在影响，三角形波纹夹芯板抗冲击性能低于单层板抗冲击性能。此外，增加芯体拓扑结构夹角能显著提高三角形波纹夹芯板的抗冲击性能，并且靶板几何形状会对其失效模式及耗能特性存在影响。     

Numerical simulation and experimental research on heat transfer and flow resistance characteristics of asymmetric plate heat exchangers

The asymmetric plate heat exchanger (APHE) has the possibility of achieving balanced pressure drops on both hot and cold sides for situations with unbalanced flow, which may in turn enhance the heat transfer. In this paper, the single-phase water flow and heat transfer of an APHE consisted of two types of plates are numerically (400≤Re≤12000) and experimentally (400≤Re≤ 3400) investigated. The numerical model is verified by the experimental results. Simulations are conducted to study the effects of N, an asymmetric index proposed to describe the geometry of APHEs. The correlations of the Nusselt number and friction factor in the APHEs are determined by taking N and working fluids into account. It is found that an optimal N exists where the pressure drops are balanced and the heat transfer area reaches the minimum. The comparison between heat transfer and flow characteristics of the APHEs and the conventional plate heat exchanger (CPHE) is made under various flow rate ratios of the hot side and the cold side and different allowable pressure drops. The situations under which APHE may perform better are identified based on a comprehensive index Nu/f^1/3.     

变截面涡旋盘高速铣削仿真加工与实验研究

为减小变截面涡旋盘涡旋齿的变形,提高加工精度,需确定合理的铣削参数。开展了变截面涡旋盘高速铣削仿真与实验研究以确定铣削参数的合理取值范围;选用HT250变截面涡旋盘为研究对象,研究了更接近实际的材料本构模型、刀-屑摩擦模型和热传导控制方程等关键技术;建立了变截面涡旋盘几何模型和简化后的二维铣削模型,利用ABAQUS软件仿真切屑成形过程及不同的铣削参数对铣削力、铣削热影响的变化曲线;通过多因素正交实验加工变截面涡旋盘。结果表明:当主轴转速为3500 r/min、每齿进给量为0.1 mm以及切削深度为2.5 mm时进行铣削更加合理。铣削变截面涡旋盘的研究为加工参数的选择提供了依据和参考;依据实验后所得的铣削参数进行铣削可减小铣削力、铣削温度及齿变形,提高了变截面涡旋盘的加工效率和质量。     

深埋矿体移动带三维圈定方法及应用

针对深埋矿山开采移动带二维圈定方法工作量大、精度低且难以满足日益增长的经济效益需求的问题，提出了一种深埋复杂矿体移动范围三维确定方法。结合沙岭金矿千米深井工程实例，在移动范围确定过程中，借助先进的3D建模技术获得三维矿山模型。该模型可以实现各类地质体的可视化，直观地展示其形态与产状，清晰地反映各构成因素间的相互关系。在3D模型中截取的特征剖面与经典移动带圈定岩移参数获取方法相结合，能轻松获得各特征剖面上的岩移参数值。通过给定的岩移参数值进而确定各特征剖面上的地表移动边界点，将各移动边界点连接即可实现矿山移动范围的圈定。研究结果表明，基于三维地质建模技术的移动带圈定方法合理可行，确定的纱岭金矿地表移动带能够兼顾安全生产与经济效益，为矿山生产开发奠定了有益基础，为类似矿山提供了有益借鉴。     

后背门内板密封面起皱问题的改善

对后背门内板拉伸过程出现的起皱问题进行了分析,并结合CAE分析制定整改方案,通过现场模具维修,消除了该处起皱问题,对类似制件的开发和模具维修有一定的借鉴作用。     

Design of a thermal management system for a battery pack in an electric vehicle using Dymola

As the world moves toward more green and efficient means of modes of transport, electric vehicles are the most suitable and ideal choice to fulfill this requirement. Rapid developments in the field of battery technology are the main reason for their progress, but thermal management in such systems has been an area of concern for a long time. The work undertaken is to design and develop a battery management system (BMS) with a specific focus on the thermal behavior of the battery pack with varying vehicle loads as well as environmental conditions. To design an efficient BMS, one needs to model the battery behavior covering the thermal as well as electrical aspects of the battery. Apart from the battery model, a mathematical model of the electrical vehicle to mimic the various road load conditions for battery also needs to be modeled. Depending on the need for cooling based on battery behavior, the cooling circuit is modeled for the battery pack used. The entire study has been carried out using Dymola, a mathematical modeling software.     

Experimental investigation of Al2O3–MgO hot hybrid nanofluid in a plate heat exchanger

Exergy–energy analysis of the plate heat exchanger is experimentally performed with different Al₂O₃–MgO hybrid nanofluid (HyNf) as a hot fluid. There were six combinations of fluids, namely, deionized (DI) water, ethylene glycol–DI water brine (1:9 volume ratio), propylene glycol–DI water brine (1:9 volume ratio), base fluids and their respective Al₂O₃–MgO (4:1 particle volume ratio) HyNfs of 0.1% total volume concentration. The effects of different flow rates and hot inlet temperatures on the heat transfer rate, heat transfer coefficient, pump work, irreversibility, and performance index (PI) are investigated. It is witnessed that the heat transfer rate, heat transfer coefficient, pump work, and irreversibility enhances with the flow rate and nanoparticle suspension. While the PI declines with a rise in the flow rate, the heat transfer rate, heat transfer coefficient, PI, and irreversibility rise up maximum for MgO–alumina (1:4) DI water HyNf upto 11.8%, 31.7%, 11.1%, and 4.05%, respectively. The pump work enhances upto 1.6% for MgO–alumina (1:4)/EG–DI water (1:9) HyNf.     

Effect of moving pictures on visual task performance and fatigue using 4K OLED and LCD TVs

This study compared the effects of 4K organic light‐emitting diode (OLED) and liquid‐crystal display (LCD) TVs on human visual task performance and fatigue when viewing moving pictures. In experiments conducted, subjects were asked to locate 35 icons among a total of 276 on‐screen icons at four moving picture speeds. From the results obtained, it was determined that OLED TVs (emissive type) exhibit superior characteristics for hit rate and false alarm rate compared with LCD TVs (non‐emissive‐type). The evaluation results of a simulator sickness questionnaire administered to ascertain fatigue levels also indicated that OLED TVs induce relatively little fatigue at fast‐moving picture speeds of 10 ppf or more compared with LCD TVs. Thus, this study confirms that OLED TVs, given their ultrafast response time characteristics, are superior in terms of moving picture images to LCD TVs.     

具有高耐蚀性和导电性的掺Cr类金刚石非晶碳的化学式解析

Cr掺杂的类金刚石非晶碳具有良好的导电性和耐腐蚀性,这对于燃料电池金属双极板涂层改性特别重要。使用团簇加连接原子模型对其非晶结构进行了详细解析,在该模型中,良好的玻璃形成材料由覆盖特征性最近邻团簇加上几个下一壳层原子的结构单元来表述。根据文献,在Cr掺杂的类金刚石非晶碳中占优势的团簇是Cr中心和C壳层的[Cr-C4]四面体团簇,然后将该团簇与适当的连接原子匹配,以满足电子轨道饱和原理。由此推导出了两个最优组成式,即[Cr-C4]CrC3(22.2%Cr)和[Cr-C4]Cr3C2(40%Cr),它们显示出良好的非晶态结构稳定性。实验结果显示,所提出的这两组化学组成的涂层材料兼具低电阻率(低至10-4Ω·cm)和优异的耐腐蚀性(腐蚀电流密度~10^-2μA/cm^2)。在sp2键含量和渗流理论的框架内讨论了导电和耐蚀的协同行为。这项工作验证了团簇加连接原子模型在具有高耐腐蚀性和高导电性的涂层材料成分设计中的可行性。